In order to increase the perforation diameter of the jet,the composite liner consisting of a spherical segment and a truncated cone was proposed,and the composite liner was studied by experiment and numerical simulation. By means of numerical simulation and three factor and three level orthogonal design experiments,the influences of radius of external circular bus,charge length diameter ratio,blast height and shell on penetration depth were studied,and the linear regression analysis was carried out. The results show that the numerical simulation is in good agreement with the experiment. With the increase of the radius of the round bus outside the spherical segment,the penetration depth decreases; with the increase of the charge length diameter ratio from 0.8 to 1.2,the change of the penetration depth is not obvious; with the increase of the blast height,the penetration depth increases; with the increase of the shell,the penetration diameter increases by more than 100%,and the penetration depth decreases by less than or equal to 20.29%.The bus radius and shell thickness are the structural parameters of the new composite liner affecting the penetration depth.
Key words
liner /
composite material /
shaped charge /
penetration /
orthogonal design
{{custom_keyword}} /
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
References
[1] WANG F,JIANG J W,MEN J B,et al. Investigation on shaped charge jet density gradient for metal matrix composites:experimental design and execution[J]. International Journal of Impact Engineering,2017,109:311-320.
[2]LEE S,HONG M H,NOH J W. Microstructural evolution of a shaped-charge liner and target materials during ballistic tests[J]. Metallurgical and Materials Transactions,2002,33(S):1069-1074.
[3]EISHENAWYA T,EIBEIHB A,LI Q M. Influence of target strength on the penetration depth of shaped charge jets into RHA targets[J]. International Journal of Mechanical Sciences,2018,136:234-242.
[4]GUO J,HE Y,XIAO Q Q,et al. Influence of yield strength of Ti-alloy liner on crater diameter formed by shaped charge jet penetration[J]. Solid State Phenomena,2017,263:30-37.
[5]YANG X H,HAN J L,LI W B. Design method of optimum standoff for bi-conical liner shaped charge warhead[J]. Transactions of Beijing Institute of Technology,2015,35(2):139-143.
[6]DING L L,TANG W H,RAN X W. Mulation study on jet formability and damage characteristics of a low-density material liner[J]. Materials,2018,11(1):1-17.
[7]XIAO J,ZHANG X P,WANG Y Z,et al. Demolition mechanism and behavior of shaped charge with reactive liner[J]. Propellants Explosives Pyrotech 2016,41(4):612-617.
[8]张雪朋,肖建光,余庆波,等. 活性射流作用钢靶侵彻爆炸联合毁伤效应[J]. 爆炸与冲击,2017,37(8):789-793.
ZHANG Xuepeng,XIAO Jianguang,YU Qingbo,et al. Penetration and blast combined damage effects of reactive material jet against steel target[J]. Explosion and Shock Waves,2017,37(8):789-793.(in Chinese)
[9]HAN J L,CHEN X,DU Z H,et al. Application of W/Zr amorphous alloy for shaped charge liner[J]. Materials Research Express,2019,6(11):115209.
[10]LIU J F,LONG Y,JI C,et al. The influence of liner material on the dynamic response of the finite steel target subjected to high velocity impact by explosively formed projectile[J]. International Journal of Impact Engineering,2017,109(1):264-275
[11]段晓瑜,郭学永,聂建新,等. RDX基含铝炸药三波点高度的数值模拟[J]. 高压物理学报,2018,32(3):035101.
DUAN Xiaoyu,GUO Xueyong,NIE Jianxin,et al. Numerical simulation of the three-wave point of RDX-based aluminized explosives[J]. Chinese Journal of High Pressure Physics,2018,32(3):035101.(in Chinese)
[12]程春,杜忠华,陈曦,等. 壳体刻槽PELE冲击破碎数值模拟[J]. 弹道学报,2019,31(3):92-96.
CHENG Chun,DU Zhonghua,CHEN Xi,et al. Numerical simulation for impact fragmentation of jacket grooved PELE[J]. Journal of Ballistics,2019,31(3):92-96.(in Chinese)
{{custom_fnGroup.title_en}}
Footnotes
{{custom_fn.content}}
