Numeric Analysis of Barrel Heat-pressure Joint Effect Based on Follow-up Boundary

YU Qingbo;YANG Guolai;GE Jianli

CN Submission Journal Articles Figures Search
Adv. Search

  • Sponsored by: China Association for Science and Technology (CAST)

    Editor-In-Chief: Xu Yida

    ISSN 1000-1093

    　

  • Hosted By: China Ordnance Society

    Published By: Acta Armamentarii

    CN 11-2176/TJ

Acta Armamentarii, a Chinese monthly journal, was first published in 1979. The journal is supervised by China Association for Science and Technology, sponsored by China Ordnance Society，and edited and published by Editorial Board of Acta Armamentarii. The Journal is included in all important domestic databases，and also collected by Engineering Index (EI, USA), Chemical Abstracts (CA, USA), Science Abstracts (SA, UK）, Abstract Journal (AJ, Russia), and Current Bibliography on Science and Technology(CBST).Acta Armamentarii has been selected into the journal Of Ordnance Science and Technology (Weapons Industry) Field Of High Quality Scientific and Technological Periodical Classification Catalogue (2022 edition), ranking T1, and the journal of Automotive Engineering Field of High Quality Scientific and technological Periodical classification Catalogue, ranking T2.
Acta Armamentarii ›› 2019, Vol. 40 ›› Issue (4) : 697-707. DOI: 10.3969/j.issn.1000-1093.2019.04.004
Paper

Numeric Analysis of Barrel Heat-pressure Joint Effect Based on Follow-up Boundary

  • YU Qingbo，YANG Guolai，GE Jianli
Author information +
History +

Abstract

In order to explore the transient impact effect of high-temperature and high-pressure propellant gas on the response to barrel strength, the finite element method is utilized to establish a three-dimensional numericalmodel for a large-caliber gun barrel. The variation of loading boundary of propellant gas with the projectile motion is defined. The evolution process of non-uniform distribution of temperature field in barrel at different moments under the first firing condition was obtained through numeric computation. The influences of thermal load, pressure and the heat-pressure joint effect on the dynamic stress response of barrel are further investigated, respectively. The calculated results show that the difference of thermal shock loads at different axial positions leads to an axial non-uniform temperature distribution, which makes the axial temperature gradient large and causes a significant axial thermal stress. In the area with intense temperature response, the compressive stress induced by thermal load and the tensile stress induced by pressure incircumferential direction make the stress componentact as the interaction between the tensile stress and the compressive stress. Compared with the gas pressure effect, the stress amplitude in the high stress region on the inner wall is weakened, and presents a trend of falling first and then rising with the temperature. Key

Key words

gunbarrel / follow-upboundary / heat-pressurejointeffect / transientimpact / numericanalysis / subroutine

Cite this article

EndNote

Ris (Procite)

Bibtex

Download Citations
YU Qingbo，YANG Guolai，GE Jianli. Numeric Analysis of Barrel Heat-pressure Joint Effect Based on Follow-up Boundary. Acta Armamentarii. 2019, 40(4): 697-707 https://doi.org/10.3969/j.issn.1000-1093.2019.04.004

References



［1］沈晓军, 张鹏翔, 孙韬, 等. 杀爆战斗部破片冲击导致火炮身管失效的准则研究[J]. 弹箭与制导学报, 2006, 26(1):84-86.
SHEN X J, ZHANG P X, SUN T, et al. Study on failure criterion of gun tube due to impaction of fragments of high explosive projectile[J]. Journal of Missile and Guidance, 2006, 26(1):84-86. (in Chinese)
[2]于情波, 杨国来, 葛建立, 等. 基于异常压力场的火炮身管断裂失效再现数值模拟[J]. 弹道学报, 2018, 30(1):80-86.
YU Q B, YANG G L, GE J L, et al. Numerical simulation on reappearance of artillery barrel fracture damage under the effect of abnormal gas flow[J]. Journal of Ballistics, 2018, 30(1):80-86. (in Chinese)
[3] 侯健, 韩肓礼. 火炮身管强度设计理论和安全系数的研究[J]. 弹道学报, 2009, 21(3):44-47.
HOU J, HAN Y L. Research of gun barrel strength design theory and safety coefficient [J]. Journal of Ballistics, 2009, 21(3):44- 47. (in Chinese)

[4]谈乐斌, 蔡樑, 袁人枢. 厚壁圆筒动态强度的有限元分析和实验研究[J]. 弹道学报, 2010, 22(4):86-88.
TAN L B, CAI L, YUAN R S. Finite element analysis and test research for dynamic strength of thick-wall cylinder[J]. Journal of Ballistics, 2010, 22(4):86-88. (in Chinese)

[5]曾志银, 宁变芳, 王在森. 身管动态应力有限元通用求解方法[J]. 兵工学报, 2005, 26(6):7-10.
ZENG Z Y, NING B F, WANG Z S. Universal finite element solution method of gun barrel dynamic stress[J]. Acta Armamentarii, 2005, 26(6):7-10. (in Chinese)

[6]CHUNGD Y, SHIN N, OH M, et al. Prediction of erosion from heat transfer measurements of 40 mm gun tubes[J]. Wear, 2007, 263:246-250.
[7]徐达, 罗业, 范文博. 火炮身管传热数值模拟及温度分布规律[J]. 装甲兵工程学院学报, 2016, 30(6):50-54.
XU D，LUO Y，FAN W B. Numerical simulation of heat transfer and temperature distribution of artillery barrel[J]. Journal of Academy of Armored Force Engineering, 2016, 30(6):50-54. (in Chinese)
[8]朱文芳, 王育维, 郭映华, 等. 某火炮身管温度仿真计算及其影响因素分析[J].火炮发射与控制学报, 2016, 37(4):58-62.
ZHU W F, WANG Y W, GUO Y H, et al. Temperature simulation calculation and analysis of influential factors of a certain gun barrel[J]. Journal of Gun Launch & Control, 2016, 37(4):58-62. (in Chinese)
[9]WUB, CHEN G, XIA W. Heat transfer in a 155 mm compound gun barrel with full length integral midwall cooling channels[J]. Applied Thermal Engineering, 2008, 28(8/9): 881-888.
[10]徐亚栋, 钱林方, 陈龙淼. 复合材料身管非线性热弹性有限元分析[J]. 兵工学报, 2007, 28(12):1428-1432.
XU Y D, QIAN L F, CHEN L M. Nonlinear thermo-elastic finite element analysis for composite material barrel[J]. Acta Armamentarii, 2007, 28(12):1428-1432.(in Chinese)

[11]武锋, 郑祖华, 吴圣川, 等. 大口径火炮多发连射炮管热力耦合分析[J]. 中国机械工程, 2012, 23(9):1056-1059.
WU F, ZHENG Z H, WU S C, et al. Thermo-mechanical coupling analysis for a large calibre gun multiround continuous firing process[J]. Chinese Journal of Mechanical Engineering, 2012, 23(9):1056-1059. (in Chinese)
[12]胡志刚, 赵建波. 速射身管发射状态下的温度场及热应力的有限元分析[J]. 弹箭与制导学报, 2006, 26(1):555-558.
HU Z G, ZHAO J B. Temperature field and thermal stress analysis by FEM for barrel in rapid fire condition[J]. Journal of Missile and Guidance, 2006, 26(1):555-558. (in Chinese)

[13]徐亚栋, 钱林方. 复合材料身管热-结构耦合分析与优化[J].弹道学报, 2006, 18(2):31-35.
XU Y D, QIAN L F. Coupled thermo-mechanical analysis and optimization of the composite material barrel[J]. Journal of Ballistics, 2006, 18(2):31-35. (in Chinese)

[14]郑小涛, 轩福贞. 热—机载荷下厚壁圆筒自增强压力与安全性分析[J]. 机械工程学报, 2010, 46(16):156-161.
ZHENG X T, XUAN F Z. Investigation on autofrettage and safety of the thick-walled cylinder under thermo-mechanical loadings[J]. Journal of Mechanical Engineering, 2010, 46(16):156-161. (in Chinese)
[15]罗来科, 宣益民, 韩玉阁. 坦克炮管温度场的有限元计算[J]. 兵工学报, 2005, 26(1):6-9.
LUO L K, XUAN Y M, HAN Y G. Finite element calculation of the temperature field for tank gun barrel[J]. Acta Armamentarii, 2005, 26(1):6-9. (in Chinese)

[16]朱文芳, 王育维, 魏建国, 等. 某火炮多发连续射击炮管传热计算分析[J]. 火炮发射与控制学报, 2010,31(2): 74-78.
ZHU W F, WANG Y W, WEI J G, et al. Calculation and analysis on heat transfer for a gun barrel during multiround continuous firing[J]. Journal of Gun Launch & Control, 2010,31(2):74-78. (in Chinese)
[17]LAWTON B. Thermo-chemical erosion in gun barrels[J]. Wear, 2001, 251: 827-838.




第40卷
第4期2019年4月兵工学报ACTA
ARMAMENTARIIVol.40No.4Apr.2019

493

Accesses

0

Citation

Detail
Sections
Recommended

/

〈 〉